Jump to content
OGXbox.com

Search the Community

Showing results for tags 'mini'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Calendars

  • Community Calendar

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 5 results

  1. The Cheapmod Mini is a modchip in a small form-factor for the Original Xbox. Based off the Cheapmod schematics, the chip comprises of a single 49LF020 (256k) LPC flash to fit (1 x 256k) custom BIOS. Features: 256k LPC flash fitted for (1x256k) custom BIOS (e.g. Cerbios). Compatible with almost any Xbox revision - from 1.0 to 1.6b. Boot imports, backups and DVDs region free without any restrictions. Running unsigned code such as homebrew and multimedia players. Installation of a custom dashboard (e.g. UnleashX). Easy to upgrade the HDD (no HDD locking required). Very easy to install - just plug-and-play via pin header. Low-cost and affordable. Free and open-source. GitHub repository: https://github.com/m4x10187/cheapmod-mini
  2. Hi all, I built an xbox mini a few years ago and designed a case based loosely on ghostavels well known xbox mini. I had it laser cut from plexiglass and it turned out ok, but could be better. I'm looking into possibly designing in CAD and making the cases but want to see if there's enough interest for it to be a worthwhile venture. I've attached some pictures of my original, any feedback or suggestions would be great. Currently it uses the breakaway part of the controller cables for controller ports, I have only used 2 on mine but 2 more can be added obviously. I also added internal wifi hence an extra cutout on the back to loop a small cat5 to an internally mounted wifi pcb, this could be omitted or the wifi pcb could be directly soldered to the ethernet port (I wanted to retain the port). There is also a small window for internal IR dongle, again this can be omitted. The 3 smaller "holes" are for hdd act LED, Power LED and network activity. Again optional. You would need to do the pico psu mod and have some aftermarket cooling for cpu etc (I used Iceberq 4 pro's) Face plates could be any colour, same for the side/back pieces. Also doesn't have to have the xbmc logo engraved Thanks
  3. Howdy! I'm having an issue with two of my xboxes and launching games within the trainer. Both of these xboxes are modchipped using the project stellar chip with HDMI+. My softmodded xbox (Rocky5) has zero issues launching the games from within Xored Mini. I've looked at the config file for xored and everything appears to be correct. I'm at a loss. Has anyone else experienced this issue? Thanks in advance!
  4. Here is my version of a slim XBOX that I designed. I tried to make the case as small as possible, and still look like an original xbox. I removed the DVD drive and the power supply from the xbox. I pulled my 1.4V xbox out of storage and it was fragging. Got tired of troubleshooting it (the clock capacitor was already removed). So I bought a 1.0 on ebay with a broken dvd drive for $15. The finish on the XBOX is not super, planning to reprint in white filament ( I ran out on my test prints), and only paint the black portions of the case. https://imgur.com/gallery/o58Nul0 I am using a Xbox 360 slim power brick to power the system. The power brick has 6 wires: 2 Yellow Wires (12V), 1 Red Wire (5V), 1 Blue Wire (Power OK, when it receives a signal back it enables the 12V rails), 1 Grey Wire (needs to be grounded to enable the 5V rail), 1 Black Wire (Gnd). The 360 slim brick outputs 5V and enables the 12V rail when it receives 5V back. I wired in a tiny 5V to 3.3V convertor on the red wire on the power brick to the 3.3 standby on my 1.0 motherboard. The Power OK on the motherboard back to the blue wire on the power brick. I then wired in a 12V to 5V 20 Amp Buck/Step Down Convertor and a 12V to 3.3V 6 Amp Buck/Step Down Convertor to the yellow wires on the power brick and connected those to the 5V and 3.3 V spots on the motherboard, and wired 12V directly. Here is a crude drawing of the wiring scheme. I added a 6 pin molex connector to the back of the case and wired it directly to the power connector socket on the bottom of the motherboard. When the power brick is enabled it illuminates the led on the brick orange and the 5V rail is active. This is being dropped down to 3.3V and going to the standby on the motherboard. When the power button is pressed the motherboard sends 3.3V back to the 360 power supply (which is high enough to enable the Power OK on the brick) and enables the 12V rail. The led on the power brick turns green. This sends the 3.3V, 5V, and 12V back to the xbox and it powers on properly. When you turn the xbox off, it removes the 3.3V from the power ok line and the 12V rails are powered off (power brick led turns orange) and the SMC is reset. My xbox powers on just fine without removing any capacitors or anything, but the flubber does stutter occasionally, but always boots up to xbmc4gamers. I installed an openxenium chip in the console. I am running indbios. The system has a 500gb 2.5 inch sata hdd. The power button I put in the case interferes with the daughter board on the 1.0 motherboard, so I unsoldered the connectors for the motherboard from the daughter board and added wires to extend the board. this board is zipped ties to an ogx360 which is soldered to a 360 rf board I salvaged from a 360 console. I do not have any original controller ports in the system as I will only use the wireless 360 controllers. These board just sit in the front of the case for now. At some point I want to develop some sort of mount for these so they are not just loose in the xbox. I designed the mount for the hard drive to use some of the motherboard screw holes to mount it to the case. The fitment for the ide-to-sata board is very tight so I removed the sata connectors from the board, and soldered on a female sata connector I salvaged from a dead 360 console. I cut the ide ribbon to about 6 inches and I am using a 6" sata cable to run to the hard drive. The ide-to-sata board is powered from the dvd drive connector. I cut a molex to sata power cable and soldered it to the ide-to-sata board where the dvd connector attaches. This allows me to put the ide board on the side of the case besides the hard drive. The case is too small to use a stock case fan, so I am using the stock fan on the gpu, a 50mm fan on the cpu, and a 50mm fan in the rear of the case. I designed the case to have ports like the stock case on the side and added them to the top of the case as well. I have not seen temps go above 50C yet. I am using Noiseblocker BlackSilentFan XS-2 for the 50mm fans. The final mod I made was to remove the stock video connector and add an internal wii2hdmi board. For future revisions I am planning the following: an attiny board to allow the 360rf board to display the controller leds and run the sync functions. I will add these leds in the case similar to how the 360 displays them. Add a sync and eject button below the power button so I can sync the controllers and get into the openxenium menu if needed. Find a better connector for 6 wires for the power as the current connector is large and doesn't mount to the case very well. (feel free to post suggestions).
  5. Hello everyone I wanted to show off my mini classic that I made. It is made from a 3d Printed case that I modeled. https://imgur.com/undefinedhttps://imgur.com/undefinedhttps://imgur.com/7GPs7sP I gave it some primer https://imgur.com/cTubiRv and some paint https://imgur.com/SDab5EQ https://imgur.com/Mek1KPw https://imgur.com/6kHrZN9 https://imgur.com/67ZuHwx Then I went the extra step and made a box for it and had it printed https://imgur.com/AK4X2Ro https://imgur.com/AURtsGc https://imgur.com/J3FOBmy Finally if you are interested, I made a video of me putting it together

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.