Search the Community

Hello everyone, my name is Vitalij and I am from latvia ! I have two xbox v1.1 and v1.6 in 1.1 dump of something (red-green light), but fully working power supply and 1.6 working, but the mosfet burned out in the power supply. Is it possible to make a 1.1 to 1.6 PSU, can there be a complete manual or something? I found a guide showing how to make from 1.1 to 1.2-1.5, but as I understand it, this does not work for me. Could you please help with this? Then I saw the topic

Hello All, I have a xbox that i picked up used, and it has a xecuter pro 2.1 (i believe) but it does not have the front or rear rs232 or DIP switch plates. When i boot i get an error of an unlocked drive, so I assume it is trying to boot to factory BIOS and it has a WD 120GB IDE drive in it. I tried to jump the D0 wire to ground as I read that would force it to use the xecuter's bios, and when I do that I get a greyscale screen that "xbox Linux Clean BIOS 1.22dev" screen that tells me to put in a disc. is this something i can do with Hexen? Thank you for any help

I have an 1T XBMC4GAMERS Original Xbox that is stuck on profiles after boot. I got it for a 6yr old and I believe he accidentally erased the original profile. I created a new profile and loaded it but it still returns to profiles after boot up where it used to go emulator menu. My email is [email protected]. I am located in Missouri USA. If anyone can help me I have PayPal and am willing to Compensate. He really liked all his games.

Hello everyone I have been working on a slim xbox build and have it 95% working the way it should with some off the shelf parts that are not the pico psu. The only sticky issue that is pretty minor is the switched power requirements. I don't really understand electronics that well past what I call a "blackbox" understanding. You know, I understand that the boards I use say they will take a certain voltage in and output whatever but no knowledge to build a more complex circuit for switching the reset line for the smc. I am using a meanwell psu that is rated for 5v20A that you can find in a lot of places on the internet. Then I am using two boards from Pololu. One to step up the voltage to 12v:https://www.pololu.com/product/2568 and another to knock the 5v down to 3.3v https://www.pololu.com/product/4090 I was wondering if you all could help me with a schematic or some understanding of how to switch on and off the 3.3v signals to help reset the smc. I have some idea that you could use some transistors maybe to accomplish this but I am not super sure. The goal here would be to use the above boards in custom pcb for future slim xbox builds. Sorry if this isn't super clear Here is the picture of my install and somewhat self evident why it could be better looking

Hi people, welp I make a upsie in my Xbox trying run pgr2, first try copy several times the game over ftp but noting works so I think well maybe is the installation of dashboard so I put another installer in my x, I guess is evox someting, was a old dvd from 2010 or 2008 based on evolutionx dash and green radioactive backgroun, anyway the trouble is, boot to original dashboard but can't boot from DVD coz I flash the DVD check disable bios so cant make a cold boot from hexen dvd to try reflash the custom dash also can't boot from original game still saying the disk is not a original one, ohhh almost forgotten say my version, is a 1.6 board with aladdin xt2 plus, evox m8 firmware with dvd check disable, I guess I need make the hot swap between my pc and the Xbox hdd, ohhh alsothis console came with a bigger hdd When I bought it but that hdd is dead (head crash ) so I put another "working" IDE drive I had laying arround the house and say working coz this disk had some bad sectors is not like 1000 bad sector just 3 sectors and works fine until I made the stupid think but that's not the point, so my question is any possibility to recovery the dash without pc xbox hdd swap, is not a problem do that I had a old desktop pc with IDE interface but I can't find my cd with linux s.o and all the stuff for softmod I burn years ago (2006 or 2007 and still working that cd) or There is a better way to flash a custom dash and boot the hexen disk

well i'm new in this site and recently i got a og xbox 1.6 so I copy a lot of games but the most wanted for me and i can't play is projec ghotman 2 the game stay in the firts part and say error disk is dirty or bad, so I copy 3 times the game and extrac the same from the 7zip file and still the problem so, i'm thinking maybe is the xbe file, so i dunno if somebody had a working defaul.xbe for pgr2 ntsc or how fix that problem yuo i know the best way is downlad copy the orignial game to the hdd again, but sadly my original copy of this game is in really bad shape, victim of v1.0 dvd drive yup my firt xbox was a 1.0 model who decides fry the nvidia chipset after 12 years (power supply problem plus caps leak) leave me alone in the 2011 anyway so if anybody had a funtional .xbe for this game plz give me a copy, i dont want download a redrump just for that

hello all, im playing some Forza Motorsport the NTCS version and the collection of trainers i have only has a couple PAL versions for this game and they don't work with my version of Forza, so im trying to figure out how to make my own, i have setup an old laptop with windows xp and found a version of the XDK and installed it, can anyone help me out with this? should i try to make a evox trainer or some other format that is compatible with xbmc4gamers ? thanks in advance

Hello everyone! This is my first post, so apologies if it’s formatted incorrectly. I’m currently having a tough time trying to diagnose what could be causing my Xbox to output a wobbly video signal as seen here. I’ve tried -swapping power supplies -replacing the 5 caps near the cpu -giving the board and console a deep clean I’m thinking maybe it’s a grounding issue? Or perhaps the video encoding chip is about to die? Honestly I’m at a loss. Any help would be very much appreciated. Thank you guys.

Hello all, -What modchip is this? -How can I update it if possible to add a 2TD HDD? Thanks in advance.

Hi, I'm new on modding OG Xbox 1.0 and after a few days reading over the net I found this thread https://www.ogxbox.com/forums/index.php?/topic/1474-identify-mod-chip/ I think it's similar to mine The problem that I have is that my HDD dies a week ago showing error 07, then I found an IDE Segate ST3802110A (80 GB), check compatibility here https://xboxdrives.x-pec.com/?p=list, from an old PC and I have also burn a DVD -R with HeXEn 2018 that I found in this forum, but when I turn on with a long press it does't read the disc and only get the error 16. I never before saw the mod chip dashboard because when I get the Xbox in 2002 they told me the mod chip only works to read non original games if I long press the power button until the led becomes red, so I don't know which version of mod chip or bios I have thats why I can't replace my HDD. After I can replace my HDD i would like to update my modchip bios and install a newest dashboard for making mi Xbox to a emulator media and take advantage of this 80 GB HDD. Thanks for your help

I just got a 1.0 Xbox with an Xcecuter 2.6 chip installed. It's running Evox M8+ and I would like to switch to the bigger X2 5035.67. what is the best way to do this? Also, is there a way to determine what is on the other bank of the chip? I get an error code when I try to boot with the other bank. Can anyone give me any advice?

Picked up a crystal green OG last week. When I power it on I’m getting 3X boot and frag. The person I bought this from suggested I flash bios but he doesn’t remember what mod chip or bios it has running now.

Hi I have installed my Aladdin xt today. I didn't expect to run into any issues as seems simple enough and I can solder small things neatly as I'm used to modifying car ECUs. I think where I have an issue is the d0 wire, none of the guides actually show it connected not can I find an image online. The guide I've followed seems to say connect the d0 point on the board to ground. I have done this I think. Please see my picture and it causes my Xbox to not boot just flashes red light. Please can someone help me with where it needs to connect to

Hi all! I need some help with switching out the hard drive in my XBOX. I've been battling with it for some time, so I decided to get some help. My XBOX version is 1.1. I currently have it softmodded with Rocky5's softmod. Originally, I had gotten a 1TB SATA drive for my XBOX (WD10EZEX-22MFCAO, which seemed like a good choice, since many other WD10EZEX drives seemed to work for others in the hard drive compatibility chart). Along with it, I got a SATA to IDE adapter, an 80-wire IDE cable, and the molex power splitter. When I first attempted to configure the drive, the exposed contacts from the back of the SATA to IDE adapter (where the power connects in) touched the back of the hard drive when I was hot swapping the IDE cable. There was a spark (I didn't think to cover the connection), and since CHIMP would never load, I assumed I had fried the drive. I ordered another one, and it wouldn't work either, so I realized it was a compatibility issue. After this, I decided to switch to a smaller, cheaper IDE drive (this Maxtor Diamond Plus 9 hard drive) that a friend said he had gotten to work before. I ordered it and attempted to configure it (using the original 40 wire IDE cable and no SATA to IDE adapter of course), and while I was able to launch CHIMP, it errors out part way through the process. Here's what I've been doing: Install CHIMP to E:/Apps, and place linuxboot.cfg into my E: drive Open the XBOX. Unplug the molex cable from the original hard drive and connect the splitter to it, one end of which I connect back to the original hard drive Place the new hard drive on top of my DVD drive (with the antistatic bag the drive came in between them) Check the mode of my new hard drive. I have tried it both with the jumper in the Cable Select Enabled position, and in Slave mode (no jumper) Launch the XBOX and wait 5 minutes for the DVD drive to go to sleep Swap the IDE cable from the DVD drive to the slave drive (within 5 seconds) Go to my applications list and launch CHIMP On the first menu button prompt, I press A to confirm that the slave drive is connected CHIMP begins to run its processes. After loading for a bit, it gets stuck on a screen saying that it can't allocate resources, with a picture of the Linux penguin in the top right I'm assuming that since CHIMP can actually boot up with this drive, that the problem might not be the drive itself, though I could be wrong (with the previous WD10EZEX drives, my XBOX would just completely freeze up when I booted CHIMP). I've tested my XBOX with just the existing hard drive installed, and that has no problems, as I'm able to play games fine and navigate through the dashboard just fine. I'm not entirely sure where my problem could be coming from, so any help would be greatly appreciated!

Looking for help with my modded Xbox. I had this done by someone (can’t remember who) back in 2005/2006 and I haven’t started it up in over 5 years. I have tried a lot of button combos and it won’t boot up. It won’t even boot up in regular mode either. No matter what I do it turns on then Immediately shuts back off. It is a Halo edition with the X3 and control panel like the one pictured above. Any help would be appreciated. Also looking for recommendations for someone that could repair it if necessary. 7253D5C9-ED2A-4D4D-A5B4-E6A12DBFF7CE.mov

OK I have the Aladdin chip installed and everything boots up fine but it still boots to the original Xbox screen what do I need to do now that I have the chip installed

I copied some emulators through ftp to the G partition of my HDD, I was using WinSCP for this. When I finished, I closed the connection and then reset my Xbox with Lt+Rt+Back+Black; I got the Bios screen, the UnleashX boot screen (I'm using a custom skin, so the skin version of the boot screen appeared) and then...nothing, just a black screen. First I thought the video was bad, but that was not the case, then I tried to boot on safe mode but nothing happened. Some people on a subreddit tell me to use Hexen to install another dashboard, I don't know if this is going to work tho. Please, if you know what's wrong with my Xbox let me know, I'm scared

Hey guys I have a 1.0 and i've been reading about splinting the 1mb tsop. I plan on just having 2 banks of 512k and have one with x2 and the other with IND. I understand that depending on which point I solder to I need to cut the trace(example a18/19). I am just double checking regarding the process. 1)once the switch is install and I select the bank(ground A18) then power on with hexen in the drive do I just go about and flash it the IND 512k bios? 2)What would happen if the switch was in the off position (middle position on a 3 position switch) where nothing is being powered or grounded? any inside would be great. And if it is a bad idea please let me know. This is the guide that I found to be most informative but I still have a few questions. https://web.archive.org/web/20150929093339/http://xbox-scene.com/articles/tsop-live-1mb.php aswell

Hello, long-time Xbox user here, and you may recognize my username from many other forums. I softmodded my console ages ago using SID 5.1.2. Recently I wanted to try it out on Xlink Kai, but I couldn't join any games in Halo or Halo 2. When I launch Halo, I get an orange ring for 15 seconds before the menu arrives. My profile is no longer there. Halo 2 tells me the DLC is damaged. Strange. So based on a few guys in the Xlink lobby suggestion, I went and used Rocky5's soft mod Quick Upgrade, which seemed to work. I had to fix a few things to restore the UnleashX dashboard skin I was using before. Anyway, I'm still having the same issues with the Halo games. 1. First question, why would I be unable to join System Link rooms? I verified Xlink can see my console fine. I even tried to create a game but was told I appear to be "offline." 2. I'm wondering if the Game Saves are screwed up and causing the issues, but I don't know of any good Save Managers to try. I attempted to open the MS Dashboard, but I get a Service Error page. 3. The system is hooked up to a CRT in 480i, so I cannot load XBMC or XBMC4Gamers because they seem to be defaulting to 720p, and the picture is a scrambled mess. How can I change that? Thanks!

https://imgur.com/a/P7rnmgZ Hi everyone Yesterday I ran into an issue with my install - I have a 1.6 Xbox so I picked up an Aladdin XT and a rebuild board to make the job easier. Should be easy right? - apparently not as I stuffed it up. Basically I made the mistake of following a video where the rebuild board had a much larger space around the pins which allowed for quite a bit of solder to be flowed onto them - I followed those instructions and when I went to put my board on it didn't sit flush. So for whatever reason I decided to solder it in and see what happened. Naturally, it didn't work so I with armed with a lot of patience and a desoldering wick I managed to remove it without destroying any pads or traces - but I have another problem. I didn't remove the unnecessary pin headers for my 1.6 - will the chip still work? and do I need to solder all of the pins to the rebuild board (I'm confused about the plating corresponding to each of the pins) as I'm not sure if I can remove them as you can see from the image the solder has gone directly into the through hole and I don't have the means of removing it. Sorry if this is stupid but I barely managed to get the header off of the board (thankfully I ordered extras) I don't want to have to desolder another one of these. Thanks!

Hi guys i just found my old xbox in the basement and by the look of things it looks like its hardmoded with a Xecuter chip and there is even a 120gb drive installed and all is working without any issues. My main question is if anyone here could help me identify what kind of Xecuter chip this is, because my plan is that i would like to replace the 120gb drive with a 1tb but im getting a LBA48 warning when i try to partition the new disk and its asking me to ugrade the current bios with a new one that supports LBA48. Current INFO: Bios: Xecuter2 4976.02 Kernel 1.00.5838.01 Xbox v1.1 What would be the best course of action, how should i approach the reflashing, what bios should i pick so that the new 1tb drive works as intended and ofcause what should i think about when i approach all this?

Hello, I bought a modchipped Xbox rev1.0. I want to remove the clock capacitor and don't want the modchip to be stuck on a clock loop, so I would like to know how to safely update the bios on the modchip through a burned CD/DVD. I've seen things like Slayers Disc and Hexen, but I'm not entirely sure how to proceed after burning them, and I'm not sure how safe it is and I don't want to screw anything up. My modchip I think is the Aladdin onde, has if you hold the power button it boots an old version (as far as I can tell) of EvoX, which besides running burned media and the logo on boot, looks just like the MS dashboard. Any help much appreciated.

so i have XBMC4gamers setup to run as an app. the trainers i downloaded from within the dash work fine but how do i add new trainers for games i have i downloaded soem new trainers but idk how to add them so that XBMC4gamers will see them

´hello guys, nice to meet you all, i recently got a modded xbox and i got coinops8 running on it, i played some good ol banjo kazooie before moving onto the main game i bought the system for, jet set radio, after ftping everything it just boots up into the sega logo and freezes, any help would be appreciated as i am a complete noob in this, i deleted the stuff in the x y and z partition and it semed to advance maybe a second more before freezing again, any help?

I have a xbox. I softmodded then removed softmod. All went well. Softmodded with unleashx and later removed. All was fine. Then yesterday went to softmod with sid. In middle of process or at end xbox shuts down like normal. Then turned back on and now red/green flashing ring and video is not working. Any ideas? I have tried letting the clock reset but made a sure not to leave the console off more than about 5 to 10 minutes. I have left it on all night trying to find a solution. I am worried if I unplug it or power it off much longer it may turn into a brick. Any ideas? I loaded and backed up everything correctly. I have 2 video cables and checked that as well and no dice any help would be appreciated. The video im sure went out with the new softmod install. Not sure why. Any help would be appreciated. Id rather fix than throw it at the wall lol.