Jump to content
OGXbox.com

Search the Community

Showing results for tags 'changing'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Rules
    • Why Can't I Download?
  • Subscribed Members Only
    • Subscribed Members Only
  • Off Topic
    • New Member Introductions
    • Rumble Pit
    • Suggestion Box.
  • General Xbox Discussion
    • General Xbox Discussion
  • Original Xbox Modding Forum
    • Hardware Mods
    • Modchips
    • TSOP Flashing
    • Softmods
    • Repair
  • Xbox Case Modding
    • Case Mods
    • Lighting & Electrical Mods
  • Tutorials
    • Official Tutorials
    • Tutorial Submission
  • Software
    • Bios
    • Dashboards
    • Installation Disks
    • Applications
    • Games
    • Emulators
    • Homebrew
  • Xbox Collecting
    • Xbox Collection Showcase
  • Rare and Uncommon
    • Rare and Uncommon Xbox Hardware
    • Rare and Uncommon Xbox Software
  • Vendors
    • N64 Freak's Products
    • Barnito's Products
  • Development
    • Rocky5's Projects
  • Online Play
    • Game Night
  • Classifieds
    • Wanted
    • For Sale
  • Moderator Section
    • Moderator Back Room

Calendars

  • Community Calendar

Product Groups

  • Vendor Forum
  • Membership Subscriptions
  • Forum Ads

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


About Me

Found 5 results

  1. I have just taken the heatsink of a v1.0, cleaned it up and replaced with MX4. It seem to work OK but the heat sink is not clamped to the CPU at all well. I can rotate it with no trouble and even rock it side to side. Were the original thermal pads adhesive? Were they 1mm thick and I need to now pack the clamp out? Any thoughts? Thanks.
  2. Hello you all, I had an idea, that involved getting an Aladdin XT 4032, and replacing the Lattice chip with an LC4064V one. I was wondering, that after flashing the chip with a JTAG programmer, that the chip would function similarly to an Aladdin Xt 4064, or not. I don't want to go into this, and end up wasting a few dollars, because I didn't ask for help before doing this.
  3. I have a 1.0 Xbox with an Xecuter 1.1 modchip installed. Used the Truhexen disk to install a brand new sata drive no issues. Trouble i am having is getting tge xbox to boot automatically to UnleashX. It only boots to the normal MS dash no matter what I select in Truhexen as my default dash. Have tried Slayer and AID clean installs choosing UnleashX but also always boots to normal MS dash. What am I missing? i did remove clock capacitor but i dont think that should matter
  4. Just a quick question guys and girls, i would like to swap my dashboard from UnleashX to EvoX, my setup is v1.2 Xbox (Softmod), is it just a simple case of popping in Hexan or Slayers installer disk in installing EvoX. Thanks all for your help, i appreciate it a lot.
  5. Hi i messed my xbox up by deleting files off the c drive and to cut a long story short ive managed to get it running again using the hexen disc, i want to boot into XBMC4GAMERS which i have on my E drive, trouble is there is no default.xbe on my c drive? there is just a IND bios config which says the following DASH1=\Device\Harddisk0\Partition2\evoxdash.xbe DASH2=\Device\Harddisk0\Partition1\Dash\UnleashX\unleashx.xbe DASH3=\Device\Harddisk0\Partition1\Dash\EvolutionX\evoxdash.xbe DEFAULTXBE=\Device\CdRom0\default.xbe not sure why it says default xbe in cd rom because i have removed the Hexen disc? any help would be appreciated.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.