Jump to content
OGXbox.com

Craiguk

Members
  • Posts

    55
  • Joined

  • Last visited

Posts posted by Craiguk

  1. On 2/13/2021 at 2:36 AM, Cosmonaut Cartilag said:

    Lucky man

    Here's on I'm working on I'm Plastic primer, gently wet flat the plastics with mild soapy water and leave to dry (Important!!!) Wipe and clean all plastics making sure there's no greasey fingerprints on it, then I applied 4 light coats of primer, before putting on your top coat, gently sand with 3000 grit sandpaper and clean ready for top coat.  3 / 4 layers of top coat applied and leave for 24 hours to dry.  Hope this helps. 

    20221215_103849.jpg

    20221215_103832.jpg

  2. Hi I'm just fixing up a cheap faulty xbox from ebay, it came with no screws, anyway the bottom Case won't fit the motherboard all the holes are 2mm 3mm off centre? Although it fits in the tin housing great. 

    No idea what version M/B it is so help would be great. 

    So far I cut 2 noggins off the bottom Case, still no joy lol. 

    See photos below. 

    https://www.dropbox.com/scl/fo/hlgzxwbzpzemvrd5j6zvv/h?dl=0&rlkey=yzsrj2j6jztmu42kj6mvczjd4

    • Like 1
  3. 6 hours ago, prtscn said:

    Try booting with disconnected HDD.

    Ok disconnected the HDD tried various Boot Disks Hexen, Slayers, AIO etc still won't boot, tried know working DVD drive still the same, only it don't FRAG straight away takes about 20 seconds.  Still on EXECUTER2 CONFIG LIVE LOADING.....  Mmmmm any ideas mate? 

    Tested suspect faulty DVD drive in my hard modded crystal and that work fine, so that's a bonus. 

    Appreciate everyones help. 

  4. Hi, Long story short i brought a v1.1 Board and PSU- TSOP with x2_5035 BIOS i was told from the seller, Then brought a Stock faulty xbox (Trace rot), installed new board and PSU into the faulty xbox, Kept he stock HDD and DVD Drive from the faulty Xbox......

    Anyway powers up (No Flubber) say's EXECUTER2 CONFIG LIVE LOADING..... and stays on that screen, Eject button FRAG's

    Is it looking for somthing from the HDD? I did try Hexen and various other Installer DVD's that work on my other consoles. Faulty DVD drive?

    Im a total TSOP noob and would appreciate some advice please, Theres a video i upped to my Dropbox so you can see what im talking about.

    Thanks all.

    https://www.dropbox.com/s/d4t4sh6u1k9zvp0/PXL_20221128_181143241.mp4?dl=0

  5. 9 hours ago, Yoinx said:

    The diagram in the post above you has the pinout exactly opposite from what you posted. Pin1 is bank1, not HDD+.

    True but the Modchip powers up,  Xbox boots and hangs just before the Microsoft word appears bottom of the screen,  any idea about the d0 I asked about please. 

  6. Brilliant it kind of boots but goes no further than the photo 🙄

    I followed this and twisted the same wires, even tried disconnecting pin 8 still same result. 

    Do I need to ground pin 7 wire to something it mentions something about d0 but I'm just not sure... See below it mentions it.... 

    1- HDD LED +ve
    2- LAN LED +ve
    3- Common +ve
    4- Modchip power in
    5- Ground
    6- Flash Protect
    7- Chip enable/D0
    8- Bank 1 select

    To power the chip you need to connect pins 3-4

    To enable the modchip as the default boot bios you need to ground pin 7 (D0) and generally pin 8 to select Bank 1

    All the LEDs are powered by pins 3 and 5 and use an inline 220k resistor.

    eg. For my setup - boot off the chip, flash protect, and using bank 1
    I connect 3-4 and 5-6-7-8
    For Bank 2 you just disconnect pin 8

    PXL_20220811_151141900.jpg

  7. Just now, nikeymikey said:

    If its not a v1.6 motherboard then why not just flash the TSOP instead of softmodding. That way you still have the advantages of a hardmod. 

    Awesome I'll take a look when I get home, but uninstalling the mod chip would make it FRAG right as it has an upgraded HDD and ata133 cable. 

  8. Okay I've just been reunited with my Crystal Xbox after 14 years in my mums loft 😎

    I has the 2.6 Modchip, HDD upgrade but the switch board is missing from the front leaving just the cable hanging. 

    I'm guessing it's going to be impossible to find one and can't find info on making a custom one, so can I remove the mod chip and soft mod it. 

    Many thanks 👍

  9. 11 minutes ago, sweetdarkdestiny said:

    3300 uF 6.3v

    mouser, digikey or if you like to gamble amazon. Everthing is should be better than this. Not to sure whats shipping costs (Germany - UK) but if not to expansiv I could send you some.

    Are there the correct ones for the v1.2 motherboard. 

    https://www.cricklewoodelectronics.com/3300uF-6.3V-Low-Impedance-Low-ESR-Radial-Electrolytic-Capacitor105-deg-C.html

    Really appreciate it

  10. 19 minutes ago, sweetdarkdestiny said:

    Holly squirrel.  (2 billion emoticons but no squirrel?)

    It's maybe a good idea to remove these caps (and the clock cap if not already) and order some new one.

     

     

     

    Yes holy squirrel is correct lol, I did the clock one a few years back, any idea where I can get replacements and what the correct values are. 

    I was thinking of RS components or Farnell as I'm in the UK. 

  11. Hi peeps, i just upgraded my 160Gb to a 500Gb Sata.  New 80 wire ide cable etc, cloned with Chimp 261812 which took 6 hours to clone drive F where the games are installed........

    Rebooted xbox and F is only showing 120Gb, so i used XBpartitioner to resize it which deleted all my games lol aggrrraaaaaaaaa..... Then F only was showing just under 300Gb ?

    The only way i could get my 500Gb was split it over F and G. 

    My setup is Xbox v1.2 Softmod Rocky5 latest version

    Sata adapter the green one with the 2 capacitors and jumper on the right

    80 wire IDE cacble

    500Gb Sata WD HDD

    Thanks all for any advice, i really appreciate it.

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.