george4541
Members-
Posts
11 -
Joined
-
Last visited
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
george4541's Achievements
Newbie (1/14)
4
Reputation
-
My bad. Meant 35
- 19 replies
-
- 1
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
I’m my case, was a bad solder joint. Fixed it on the third time flowing out the solder. Not sure why after 5 years of storage it would have gone bad. While I was in mourning for it before getting it fixed, I found another used Xbox online with an xecuter chip, hard drive loaded with over 3 games, and 4 controllers for $70. Will take delivery tonight and hope all is well with this unit.
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Thanks for all the help guys. resoldering the 9 and 15 again fixed ther issue All good and chip up and running
- 19 replies
-
- 2
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
I see what you say on page 13 about the led but I dont see any other led on the board other then the two either side of the switch connector and the one for the write protect switch.
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Thanks. Not getting the 3.3 v to the chip or the pins on either the 9 or 15 Pin. will recheck the soldering again
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
I know. thats why I went back to recheck and redo all of the solder joints. Installation was complete and working before the unit was put away for several years. Going to check the voltage at the back of the mod chip on the pin header conections to see if its seing the 3.3 v. I guess that should be pins 9 and 15 according to the instructions
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Seating and tipping the xecuter board has no effect. I notice that the 3.3 volt light does not come on. What should I check?
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Still not having any luck. Just finished going over all of the solder connections on the Rebuild PCB, and still no go on getting the chip to launch or light up the front switch.
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
I also noticed that it does nor retain the current date and time. Could that have any impact?
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Thanks for the reply. I noticed that, and tried to boot up without installing the drives, and same issue. Even with it straight and fully seated, does not launch evox or have a light on the switch. I've tried resoldering the connections, and same issue. Is there a certain connection or voltage i should be looking for in the pins?
- 19 replies
-
- 1
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
-
Thanks for your offer to help. I have an xbox version 1.6 that was modded several years ago and has been in storage. Now it wont boot up evox and the lights on the external switch do not nome on. The only light on the chip that's on is the blue light. Any thoughts?
- 19 replies
-
- xecuter 3
- xapt3r 1.6
-
(and 5 more)
Tagged with:
Board Life Status
Board startup date: April 23, 2017 12:45:48