Jump to content
OGXbox.com

Leaderboard

Popular Content

Showing content with the highest reputation on 12/05/2017 in all areas

  1. I'm after a little help with this. Do you folks have a GOOD link to a Video on exactly how to install a 2TB drive reliably? I'm struggling to figure out the best reliable method on how to do this... Setting up partitions, with what apps etc.. I installed a 500GB IDE in my xbox but it's been nothing but trouble. so I obviously didnt do it the correct way Any help, advice, links or even better for the forum, a post with details, application downloads and images for a walk through. Thanks very much in advance!!
    1 point
  2. Ive cloned about 7 drives using this product offline http://a.co/f5SsvbY Works great without any issues.
    1 point
  3. Great info from poster above - I do 2TB drives all the time and have some quick notes on the setup. What's needed - 2TB drive, 80 wire 40 pin IDE adapter, Sata/Ide adapter This adapter will workhttp://www.ebay.com/itm/Female-SATA-SSD-HDD-Hard-Drive-To-IDE-3-5-40-Pin-Male-Converter-Adapter-7-15P-/172719304915?epid=2264787562&hash=item2836df70d3:g:UWUAAOSwal5YEEAL Step 1: Typical soft mod - or go right to mod chip Step 2: Softmod - Replace IDE cable with new one, put adapter on new drive and set the jumper on the adapter to slave. I usually take a game case and anti static hard drive sleeve and lay on top of the dvd drive, placing HDD on top of that. so the back of the adapter isn't too far from the IDE connection of the DVD drive. Use latest chimp from Rocky5 Softmod tool, hot swap IDE connector to hard drive and clone master to slave. Step 2 - TSOP - Using original hard drive still, bridge your points and flash new BIOS using HeXen or other preferred utility - make sure you flash a Bios that has LBA48 support. Examples are: IND-BIOS 5003, Evox M8 (F&G) X2.5035. Step 3 - TSOP/Softmod - Install drive (for TSOP), set jumper to master. TSOP you will just start new drive setup with HeXen, and install applications from CD on E partition (this will put XBparitionner.. Softmod tool may handle your partition/cluster sizes correctly, I do mostly TSOP but install XBpartitioner in your apps folder on E to double check. FORMATTING THE DRIVES - here is the trick/easy way to do it. Do this from UnleashX dashboard not from HeXen CD. load it up XBpartitioner v1.3, and hit the A button until you see the 927GB as shown above in the picture. from the poster before me. Now, before formatting highlight partition 6 and use the right d-pad to change that value to the next increment down (926GB). Repeat this step for Partition 7. Now format. After format is complete, exit/restart. You will see like 486GB on F and nothing in G. Load Xbpartitioner again, and set both values to 927 (max) and re-format. When you restart you will have 949,000 MB on each partition and they will be at 64K.
    1 point
  4. I'm after a little assistance if you can. I've TSOP'd one of my units successfully for the first time so I'm rather happy. I'm now trying to upgrade the Hard Disk and I have the Hexen 2017 burned. I've installed the HDD and it's detected by Hexen at boot and formatted it all ok. Problem I have now is in the menu I'm trying to basically install a dash etc.. and its asking for a password. I'm entering the password as shown on the screen but it says password is wrong. I've attempted this a few times and I know I'm entering the password correctly but it's not accepted. Am I missing something or am I just dumb? Any help would be fantastic.
    1 point

Board Life Status


Board startup date: April 23, 2017 12:45:48
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.