Search the Community
Showing results for tags 'wireless'.
Found 5 results
Does anyone have any tips for making the controller s wireless? My understanding is that the yellow wire isn't needed and the posts are just usb 1.1. I can fit a 5v battery in the controller and I can get a recharge circuit, so that's the battery covered. Would 2 of these be suitable to solder, one in the controller and the other inside the xbox? https://www.ebay.co.uk/i/202172642349?chn=ps&ul_ref=https%3A%2F%2Frover.ebay.com%2Frover%2F1%2F710-134428-41853-0%2F2%3Fmpre%3Dhttps%253A%252F%252Fwww.ebay.co.uk%252Fi%252F202172642349%253Fchn%253Dps%26itemid%3D202172642349%26targetid%3D520884085919%26device%3Dm%26adtype%3Dpla%26googleloc%3D1006816%26poi%3D%26campaignid%3D1594021339%26adgroupid%3D62960991511%26rlsatarget%3Dpla-520884085919%26abcId%3D1139126%26merchantid%3D118951391%26gclid%3DCjwKCAiAgrfhBRA3EiwAnfF4tlNEH_Khzzqr0_gSwgxwiTNZS9s4t5kY_-pYXpeb-v4Px1HkMcnrhhoCYvIQAvD_BwE%26srcrot%3D710-134428-41853-0%26rvr_id%3D1805951190053%26rvr_ts%3D17ace08c1680aaa276b2dfd6ffd10d47 Any help would be great
Hi all, Long time modder and lurker, first time poster but I wanted to share a project I have been working on the last couple months. It is a small PCB which allows you to use Wireless Xbox 360 controllers (via the Xbox 360 USB Wireless Receiver) on an OG Xbox console. The design is loosely based on another similar project I did for the Nintendo 64 console https://imgur.com/gallery/HVLea3d Following the release of this board another forum user sent me an email asking if this device could be adapted for the OG Xbox, and funnily enough that was the next thing I was going to attempt! I wanted to support the following features atleast: Up to four players with rumble support. 100% USB Bus Powered so no external power supply needed. Fast bootup time, so it's up and running in time for the OG Xbox. Low input lag. As always, this is a hard thing to measure, however I can say that an OG Xbox controller is polled by the console every 4ms or so. My software gathers all the Xbox 360 wireless controller data, collates it and generates all the HID reports every 4 ms aswell. It's possible an input may miss this 4ms window, so would happen in the next 4ms window. As you probably know, an OG Xbox controller is basically a USB HID device, however it has some custom requests and other slight differences, meaning that it doesn't work on a Windows machine without a custom driver, and conversely a generic HID controller will not work in an OG Xbox so there was some work in getting a reliable and compatible solution working. To support four controllers, it is necessary to have 4x Full USB device controllers. However I imagine most people would rarely play with 4 people at once so my design is modular meaning you can support anywhere from one up to 4 players as required to keep cost down. This is a link to the github repo with what I came up with https://github.com/Ryzee119/ogx360 Cheers!
I'm interested in converting the original wired "S" controller into a wireless controller using the guts of an off brand wireless controller like a Logitech. To anyone's knowledge has this been done before or at least something similar?
I would like to purchase a Logitech wireless controller. It must be in working condition. I have receiver, so it is not a must, but I understand if someone wants to sell controller with receiver. Colour does not matter, but white is the least wanted one. Sent fra min NX551J via Tapatalk
Alright guys. The time has come. Here I'm gonna be adding an internal WiFi adapter to my OG Xbox because, lets face it, Wires are ugly, they get chewed by your dogs and people trip over them. and come on WiFi in an OG Xbox!! Heres a list of Tools and Materials you'll need Torx T20 Torx T10 Soldering Iron Solder Drill with assorted bits Wire Cutters Heatshrink or Electrical Tape Multi-Meter Dremel with cutting disc or small hand saw. Assorted files or sand paper Wireless bridge gaming adapter RP-SMA Female to Male Pigtail Rj45(Ethernet) Female to Male adapter some Motherboard standoffs with matching screws I got the idea from the youtube user "Thewheelman282" Link to video https://www.youtube.com/watch?v=3zG8DQ3Omfk To start you'll need to pull apart your console. I'm not gonna explain how to because there are Many sources for this elsewhere. Next you need to figure out where you want to mount the adapter. again I'm doing what he did in the video and mounting it to the bottom of the DVD drive. If doing the same you'll need to pull apart your DVD drive too. Every drive is different, mine is a Samsung with 4 screws on the bottom. Once you have the bottom half of your drive, You'll want to Pull apart your adapter and mark out your mounting holes. Now use your drill to drill them out. Start small, you can always make the hole bigger if you need to. Time to add the MoBo standoffs, I used 6 of them and cut the screw part off the ones that go inside the drive. Now you can mount your adapter and put your drive back together. Now its time to start cutting wires. Get your multi-meter and determine what wires you need to splice into. Since my adapter uses 5v I used Pin 01(Ground) and Pin 08(5V) Heres the Pinout for the Drive side of the DVD plug Next your gonna need to figure out where you want your adapters Ethernet port to be. I used the same location as in the video for simplicity. Now your gonna want to get your RJ45(Ethernet) Male to Female converter/Extension and see if it will fit. (Mine did not so i had to trim it down) In the process of trimming it, I nicked a few wires so I had to pull it completely apart to trace each pin with a multi-meter and solder each wire back into place. (Dont make the same mistake I did and take your time!!) I was impatient and rushing. now you can Take your dremel and start cutting the hole for your RJ45 port, Once cut it should look something like this.(Again I was rushing, So its not as clean as Id like it to be) you'll want to test fit the plug, then clean up the cuts with a file or sand paper. Then mount your new port to the top of the existing one. I used a few drops of Super glue to accomplish this. \ Now you'll need to drill a hole for your RP-SMA Pigtail. (Antenna extension wire) I chose to put it beside the Ethernet ports. Ignore ignore the hole by the Ethernet port. Thats for my USB ports. I put a piece of heatshrink around the metal antenna connector so it doesnt cause any shorts or problems once its put back together \ Its a tight sqeez but everything fits inside nicely, just be patient while your putting things back where they go. Now you can put it all back together so you can Admire all your hard work and enjoy your now Wireless Xbox. Let me know what you guys think. This is my FIRST Tutorial/Write up. Tried to give clear info, If you need any additional info ill be glad to help out.
Board Life Status
Board startup date: April 23, 2017 12:45:48